- Sektör: Oil & gas
- Number of terms: 8814
- Number of blossaries: 0
- Company Profile:
A chemical used to break emulsions (that is, to separate the two phases). The type of demulsifier selected depends on the type of emulsion, either oil-in-water or water-in-oil. Demulsifiers are used in the chemical analysis of oil and synthetic muds and to treat produced hydrocarbons.
Industry:Oil & gas
A chemical whose molecular structure can envelop and hold a certain type of ion in a stable and soluble complex. Divalent cations, such as hardness ions, form stable and soluble complex structures with several types of sequestering chemicals. When held inside the complex, the ions have a limited ability to react with other ions, clays or polymers. Ethylenediamine tetraacetic acid (EDTA) is a well-known sequestering agent for the hardness ions, such as Ca<sup>+2</sup>, and is the reagent solution used in the hardness test protocol published by API. Polyphosphates can also sequester hardness ions. The addition of sodium acid pyrophosphate (SAPP) to a cement-contaminated mud renders the calcium ions essentially nonreactive with clays in the mud. As a side benefit, SAPP also lowers mud pH. Sequestering is not the same as precipitation because sequestering does not form a solid.
Industry:Oil & gas
A fluid described by a three-parameter rheological model. A Herschel-Bulkley fluid can be described mathematically as follows: <br><center><img src="files/OGL99112. Gif" alt="Herschel-Bulkley fluid" border="0" vspace="8" /></center><br>The Herschel-Bulkley equation is preferred to power law or Bingham relationships because it results in more accurate models of rheological behavior when adequate experimental data are available. The yield stress is normally taken as the 3 rpm reading, with the n and K values then calculated from the 600 or 300 rpm values or graphically. <br><br>Reference:<br>Hemphill T, Campos W and Pilehvari A: "Yield-Power Law Model More Accurately Predicts Mud Rheology," Oil & Gas Journal 91, no. 34 (August 23, 1993): 45-50.
Industry:Oil & gas
A flow of formation gas in the annulus between a casing string and the borehole wall. Annular gas flows occur when there is insufficient hydrostatic pressure to restrain the gas. They can occur in uncemented intervals and even in cemented sections if the cement bond is poor. After cementing, as the cement begins to harden, a gel-like structure forms that effectively supports the solid material in the cement slurry. However, during this initial gelling period, the cement has no appreciable strength. Hence, with the solid (weighting) material now supported by the gel structure, the effective density of the slurry that the reservoir experiences falls rather suddenly to the density of the mix water of the cement, which is usually fresh water, whose density is 8. 34 lbm/gal, or a gradient of 0. 434 psi/ft of vertical column height. Various chemical additives have been developed to reduce annular gas flow.
Industry:Oil & gas
A flow of formation fluids into the wellbore during drilling operations. The kick is physically caused by the pressure in the wellbore being less than that of the formation fluids, thus causing flow. This condition of lower wellbore pressure than the formation is caused in two ways. First, if the mud weight is too low, then the hydrostatic pressure exerted on the formation by the fluid column may be insufficient to hold the formation fluid in the formation. This can happen if the mud density is suddenly lightened or is not to specification to begin with, or if a drilled formation has a higher pressure than anticipated. This type of kick might be called an underbalanced kick. The second way a kick can occur is if dynamic and transient fluid pressure effects, usually due to motion of the drillstring or casing, effectively lower the pressure in the wellbore below that of the formation. This second kick type could be called an induced kick.
Industry:Oil & gas
A floor hand, or member of the drilling crew who works under the direction of the driller to make or break connections as drillpipe is tripped in or out of the hole. On most drilling rigs, roughnecks are also responsible for maintaining and repairing much of the equipment found on the drill floor and derrick. The roughneck typically ranks above a roustabout and beneath a derrickman, and reports to the driller.
Industry:Oil & gas
A finely divided, solid material, which when dispersed in a liquid medium, scatters a light beam and does not settle by gravity; such particles are usually less than 2 microns in diameter. Some drilling fluid materials become colloidal when used in a mud, such as bentonite clay, starch particles and many polymers. Oil muds contain colloidal emulsion droplets, organophilic clays and fatty-acid soap micelles.
Industry:Oil & gas
A filtration process in which the slurry being filtered remains static. Filter cake continues to grow thicker as filtration continues. Under static conditions, no cake erosion occurs. In theory, the filtrate volume increases as the square root of elapsed time, ignoring spurt loss.
Industry:Oil & gas
A filtration process in which the slurry being filtered is being circulated over the filter cake, so that the cake is simultaneously eroded and deposited. The erosion rate depends on the shear rate of the fluid at the face of the cake. If the shear rate remains constant, cake thickness and filtration rate reach steady state, usually in a matter of hours. When the conditions change, a new steady state will be established.
Industry:Oil & gas
A female threadform (internally threaded) for tubular goods and drillstring components.
Industry:Oil & gas