- Sektör: Oil & gas
- Number of terms: 8814
- Number of blossaries: 0
- Company Profile:
A large-diameter, relatively low-pressure pipe string set in shallow yet competent formations for several reasons. First, the surface casing protects fresh-water aquifers onshore. Second, the surface casing provides minimal pressure integrity, and thus enables a diverter or perhaps even a blowout preventer (BOP) to be attached to the top of the surface casing string after it is successfully cemented in place. Third, the surface casing provides structural strength so that the remaining casing strings may be suspended at the top and inside of the surface casing.
Industry:Oil & gas
A large-diameter pipe that connects the subsea BOP stack to a floating surface rig to take mud returns to the surface. Without the riser, the mud would simply spill out of the top of the stack onto the seafloor. The riser might be loosely considered a temporary extension of the wellbore to the surface.
Industry:Oil & gas
A large-diameter (3- to 5-in. Inside diameter), high-pressure flexible line used to connect the standpipe to the swivel. This flexible piping arrangement permits the kelly (and, in turn, the drillstring and bit) to be raised or lowered while drilling fluid is pumped through the drillstring. The simultaneous lowering of the drillstring while pumping fluid is critical to the drilling operation.
Industry:Oil & gas
A large valve used to control wellbore fluids. In this type of valve, the sealing element resembles a large rubber doughnut that is mechanically squeezed inward to seal on either pipe (drill collar, drillpipe, casing, or tubing) or the openhole. The ability to seal on a variety of pipe sizes is one advantage the annular blowout preventer has over the ram blowout preventer. Most blowout preventer (BOP) stacks contain at least one annular BOP at the top of the BOP stack, and one or more ram-type preventers below. While not considered as reliable in sealing over the openhole as around tubulars, the elastomeric sealing doughnut is required by API specifications to seal adequately over the openhole as part of its certification process.
Industry:Oil & gas
A large valve at the top of a well that may be closed if the drilling crew loses control of formation fluids. By closing this valve (usually operated remotely via hydraulic actuators), the drilling crew usually regains control of the reservoir, and procedures can then be initiated to increase the mud density until it is possible to open the BOP and retain pressure control of the formation. BOPs come in a variety of styles, sizes and pressure ratings. Some can effectively close over an open wellbore, some are designed to seal around tubular components in the well (drillpipe, casing or tubing) and others are fitted with hardened steel shearing surfaces that can actually cut through drillpipe. Since BOPs are critically important to the safety of the crew, the rig and the wellbore itself, BOPs are inspected, tested and refurbished at regular intervals determined by a combination of risk assessment, local practice, well type and legal requirements. BOP tests vary from daily function testing on critical wells to monthly or less frequent testing on wells thought to have low probability of well control problems.
Industry:Oil & gas
A large tank that holds drilling fluid on the rig or at a mud-mixing plant. For land rigs, most mud pits are rectangular steel construction, with partitions that hold about 200 barrels each. They are set in series for the active mud system. On most offshore rigs, pits are constructed into the drilling vessel and are larger, holding up to 1000 barrels. Circular pits are used at mixing plants and on some drilling rigs to improve mixing efficiency and reduce dead spots that allow settling. Earthen mud pits were the earliest type of mud pit, but environmental protection concern has led to less frequent use of open pits in the ground. Today, earthen pits are used only to store used or waste mud and cuttings prior to disposal and remediation of the site of the pit.
Industry:Oil & gas
A large molecule made up of repeating units. Some polymers are naturally occurring, such as xanthan gum, guar gum and starch. Other polymers are modified natural polymers, such as carboxymethylcellulose (CMC) and hydropropyl starch and lignosulfonate. Some are synthetic such as polyacrylates, polyacrylamides and polyalphaolefins. Polymers may be classified by their structure and may be linear, branched or less commonly cyclic. Copolymers contain two or more different monomers that can be arranged randomly or in blocks. In solution, entangled polymer chains can create networks, giving complex viscosity behavior. Polymers that ionize in solution are called polyelectrolytes. Charged groups strongly affect behavior and interactions with colloidal clays, other polymers and solvents. Molecular size (weight) influences how a specific polymer type performs in a given type of mud. A small polymer may be a deflocculant, whereas a large polymer of the same type may be a flocculant. Some are viscosifiers and others are fluid-loss control additives while others are multifunctional.
Industry:Oil & gas
A laboratory test used to determine if a drilling fluid blocks movement of filtrate through pore spaces of a shale sample. The PPT device monitors the increase in pore pressure in a shale when exposed to a drilling fluid over a period of time. Shale cores from 1 to 3-inches long are fitted into a modified Hassler cell that has sensitive pressure transducers in reservoirs on each end of the cell. <br><br>Reference:<br>van Oort E, Hale AH, Mody FK and Roy S: "Transport in Shales and the Design of Improved Water-Based Shale Drilling Fluids," in SPE Drilling and Completion 11, no. 3 (September 1996): 137-146.
Industry:Oil & gas
A laboratory test to evaluate drilling-grade weighting material for potential abrasiveness. The test measures weight loss of a specially shaped, stainless-steel mixer blade after 20 minutes at 11,000 rpm running in a laboratory-prepared mud sample. Abrasiveness is quantified by the rate of weight loss, reported in units of mg/min. Mineral hardness, particle size and shape are the main parameters that affect abrasiveness of weighting materials. Some crystalline forms of hematite grind to a higher percentage of large particles than do other forms and are therefore more abrasive. Hematites are harder than barites, grind courser and are more abrasive. Thus, a hematite that is proposed as a weighting material for mud is typically a candidate for abrasion testing.
Industry:Oil & gas
A laboratory test or other assessment utilizing a living organism, such as mysid shrimp, to determine the effect of a condition to which the organism is exposed. Such tests are performed under controlled environmental conditions and duration. Bioassay tests of drilling fluids are required by governmental agencies throughout the world prior to discharge of mud or cuttings. The organisms used in bioassays are those found in the area that would be most affected by contact with the proposed drilling fluid. The dosage of interest is typically the lethal concentration, known as LC<sub>50</sub>, that will kill 50% of the population of organisms in a given period of time. Chronic bioassay tests indicate sublethal effects, such as changes in growth or reproduction of the organism over a longer period of time.
Industry:Oil & gas